Poker Craps And More

Public liability indemnity is suggested as all corporations are at risk to some quantity. Even though nothing bad has yet occurred to your companies premises, will not mean that it will not at some point in near the future. If someone is wounded, or their property lost, it is your contractual requirement to appropriately compensate them. This cost can easily be shockingly expensive, depending on the exact case.

Fortunately, you do have a chance to guard yourself for this likelihood. Getting public liability insurance permits you to breathe a touch easier. If a customer claim is pricey, the insurance corporation will be there to supply you with a protection net. Its their legal duty to guarantee that you are covered from any claims and legal expenses. This leaves you available to concentrate on actually doing business, instead of thinking about what may possibly happen. Following are numerous examples of times when public liability cover have in the past come in handy. Looking for business insurance? Contact Insured Risks for Professional Indemnity Insurance.

Directors of plumbing firms as a rule get the job finished quick and right. Although, from time to time something may possibly go seriously wrong. If you smash up a customer’s gas pipes while on the job, affecting property for example personal computers & carpeting, public liability cover will be there to pick up the invoice.

Another illustration is that of a promotions company. If a customer were to break an ankle in your place of work, even if it’s not your fault, you would be held legally answerable. Nonetheless, with public liability insurance you would not have to resolve the claim at all.

In a comparable example, injury caused to a passerby by a worker on a construction site is the liability of the organisation’s director. This sort of claim can easily get very pricey indeed, unless you obtain the right insurance cover.

Have you ever come across power problem where once you switch on the power supply and the fuse blow? You have checked all the components in the power (primary) and secondary section and all the components seems to be ok! Where is the fault? A fuse blown are usually caused by a shorted bridge rectifier, defective posistor, power transistor or FET, shorted primary winding of switch mode power tranformer, shorted secondary diode and etc. But in this article i’m gone to show you another secret of electronic troubleshooting tips.

I got frustrated as to where is the cause of power problem. Everytime when i switch on the power supply the fuse blow immediately (the fuse became dark color and this indicate that there is a major short circuit in the power supply). I have checked all the components in the power supply and can’t find the culprit! What i do is i desoldered all the suspected parts one by one and replaced with a known good component. I eventually found the caused of the power supply problem. Guess what? It was the main filter capacitor (220 microfarad 400 volt). After replacing the filter cap the power supply worked perfectly fine. I begin my detective work to find out why this capacitor can caused the fuse to blow eventhough i already confirmed it ok with my meters.

The meters that i used to check the filter cap were analog meter, digital capacitance meter and esr meter. In this article i will not explain about how to check capacitor or testing capacitor and how capacitor work. I believed most of you know how to check capacitors and also generally using this type of meters. Measured with analog it showed capacitor charging and discharge, with digital capacitor tester it showed around 220 microfarad and with esr meter it showed low esr reading!

This proved that the bad capacitor breakdown when under full operating voltage. Then, how do i confirm that this filter capacitor is faulty? By using an analog insulation tester. When i connect the faulty cap to the meter and press the go button-it showed a very low resistance and this is the proved of short circuit between the plate when voltage applied! There is nothing to do with bad electrolyte. A good capacitor will just showed a charge and discharge in the insulation meter just like you are checking a capacitor using analog multimeter. In the market there is quite a number of ranges that you can buy. It has the range of 50v, 100v, 250v, 500v, 1000v and even 5000v! If you want to test a capacitor of 100 microfarad 160v then you have to select 100v. If you select 250v, it will blow your capacitor that is under test.

If you have the SENCORE TEST EQUIPMENT such as the sencore lc meter LC102 OR LC103, these meters have the capabilities of checking any type of capacitors with four test; -testing for capacitor values -checking for leakage -equivalent series resistance (ESR) and -Dielectric absorption It can check aluminum electrolytic capacitor, film capacitor, ceramic, high voltage capacitor and etc.

Conclusion-Different capacitor manufacturer produced different type of quality of a capacitor. Perhaps the bad capacitor that i encountered are from the lowest grade one. A capacitor failure when under load is very rare. Using ESR capacitor meter alone can solve most of the electrolytic capacitor problem.

Pattern Equipment & Prototype (PEP) in Windsor, Ontario, is a division of Tooling & Equipment International (TEI), Livonia, Michigan. TEI is a leader in Design, Engineering and Manufacturing of Tooling, Prototype, Pre-Production and Mass Production Equipment for the Metal Casting Industry.

PEP selected Encompix (www.encompix.com) ETO ERP (Enterprise Resource Planning) software because it has filled the manufacturing software requirements of Engineer-to-Order companies since 1992. The company name reflects the commitment to developing business application solutions that encompass the complex areas of project-based and job-based manufacturing.

Engineer-to-order (ETO) and project-based manufacturers face business challenges that simply cannot be resolved by traditional manufacturing systems. Engineer-to-order companies need to be able to provide accurate cost estimates to customers, manage all aspects of complex projects, deliver on time and on budget–all while keeping a close eye on cash flow. There is intense pressure to reduce costs, shorten cycle times, while maintaining high quality. Finally, engineer-to-order companies need an accurate picture of the profitability of each project in order to comprehend the impact on the business.

In the increasingly competitive world of engineer-to-order and project-based manufacturing, companies have to operate at maximum efficiency to compete with not only domestic firms, but also the growing number of overseas competitors. The companies that will thrive in this environment are those that are continually looking for improvement.

According to Thomas R. Cutler, spokesperson for the ETO Institute (www.etoinstitute.org), “Encompix has experienced strong levels of success because this year few other manufacturing software companies truly understand the specific issues and nuances facing the engineer-to-order segment of the manufacturing market.” Encompix provides ETO manufacturers with a competitive advantage by improving bottom line results. Encompix www.encompix.com Roger Meloy 513-733-0066

# # #